Slot Machine Parts. If you came looking for slot machine parts, you’ve come to the right place. East Coast Slots has one of the largest slot machine parts inventories in the nation from LEDs to full conversion kits. If it goes anywhere inside a slot machine, we probably have it.
IGT Power Supply for 200 Series $ 29.99 Read more; IGT Nickel Shelf Wheel $ 4.99 Read more; IGT Handle Assembly Plate $ 9.99 Add to cart; IGT Handle Hub $ 9.99 Add to cart; IGT Fuse Caps $ 9.99 Read more; IGT Door Optics $ 24.99 Add to cart; IGT Dollar Coin Head $ 4.99 Add to cart; IGT Coin Comparitor Clips $ 9.99 Read more; CC-16-D SMALL COIN.
Hoppers run on AC power yet the MPU that tells it to cash out runs on DC voltage. In order to do this a small interface called an SSR (Solid State Relay) is placed in between the MPU and the hopper. An SSR is a device in which DC voltage can control AC voltage.
The SSR will rarely go bad but if you have to check the power going to the hopper. This is where to check.
Once the cash out Button has been pressed the MPU send a signal through the SSR to the Hopper to begin cashing out. The coin out-optics or switch on the Hopper report back to the MPU, telling it how many coins has been paid out. Once the correct amount of credits has been given, the MPU shuts down the Hopper.
To test the hopper for the PE-Plus press the white self-test button to the test hopper page. Turn the reset-key to activate the hopper payout. This test page will pay out ten coins and is useful to see if the hopper is operating properly.
Parts List for the IGT S+ Reel Slot Machine Buy Sell Trade & Repair Slot Machines and Casino Gaming Equipment and Tables. IGT Hopper Knife for Large Coin.
To run this test with the S-Plus push the white self-test switch until you see a “ 3 “ in the Coins Played Window then hit the spin button.
There is also an option located on the output page that will allow the hopper to run constantly until you stop it. To do this for the PE-Plus simply go to the output page use the deal-draw button until the arrow points to “HOPPER ONE” or “HOPPER TWO” ether one will work. When you turn the reset key, the hopper will run until you let go of the key.
For the S-Plus go to output page “ 2 “ then the turn the reset key to “ 35 “ once the spin button is pushed it will run until you let go.
The number one thing to go wrong by far is coin jams especially if you have a bar-top or slant-top game. Slant-tops and bar-tops have what is called the escalator that the coins have to slide up in order to get to the coin out tray. Any bent or foreign coin will jam up and cause general mayhem. If you are lucky, enough to have an upright game (because there easier to fix) then the bad coins will most often cause the coins to go under the knife.
The coin-out optic is located at the point where the coins exit the hopper. The coin-out optic tells the MPU how many coins have left the machine. If they go bad, they will generally cause a coin-out tilt. Most often, the wires leading to them are cut or mangled and no signal gets back to the MPU. Sometimes they get dirty and just need cleaning by blowing on them. (If the optics ground wire is not properly grounded it will cause a hopper runaway)
To remove the hopper simply open the door “or doors” remove the coin-in assembly and pull it out. If you have an upright game, you will not have to pull out the coin-in assembly since they are built into the door.
The hopper is connected to what is called the MOLEX connecter. All the wires from the coin-out optics and ac power for the hopper motor run through this.
The main components of a hopper depend on your game cabinet and game version. The most common are:
• Knife: This is what the coins slide up on to exit the hopper.
• Shelf and Shelf Wheel: These are to plates one smaller than the other that the coins ride up on out of the bowl and to the knife.
• Agitator: This is a star shaped thing usually made out of rubber or hard plastic that sits on the shelf in the middle of the bowl and stirs up the coins so they ride out.
• Escalator: This is for bar-top and slant-top models so when the coins exit the hopper they ride up the escalator and exit into the tray.
• Coin-Out Optics: Senses when a coin has or has not exited the hopper and informs the MPU.
Igt Slot Machine Troubleshooting
Working on hoppers is not a fine science the only electric components are the coin-in optics and the electric motor. The electric motor can be hooked up to a wall socket to see if it works. Warning this is not suggested to be done because of obvious hazards and a proper test cord should be used when testing the motor.
If the coin-out optic is having a problem the hopper will still work in test mode and will spit out coins. Everything else on a hopper is mechanical and was learned after years of having to fix them. Often slot techs carry their own home made tools and have deferent methods of repairing them.
Before ticket in ticket out I used to carry around five pounds of tools and parts to fix them, while other slot techs would just carry a screw driver to fix a hopper. Basically if you have mechanical experience working on things like cars or truck's you will most likely not have many problems. If you do not have mechanical experience then remember how things come apart so you can put it back together again. Write it down or take pictures if you have to. Sites to check out http://myhomereviewsblog.com/backtrack-compatible-wireless-adapters-review
IGT S-Plus, S2000 or S2000 Vision
IGT model identification one machine is always confusing. They look so much alike that if you don’t know what to look for then you probably just guess or go by what someone tells you that it is. Many of the games are available in more than one model of machine so knowing which machine is which is important.
S-PLUS – There are 3 ways this machine can be identified. Usually these machines have six serial numbers on the right side The ‘Winner Paid’ and ‘Credits’ meters are to the left of the center of the reel glass. The also have the motherboard behind the hopper.
S-2000 – Almost any part of these machines can be upgraded, doors,bill and I think you can get different colored speakers. You can identify these by the long meter to the left of the reel glass, the serial number is seven numbers on the side or you may notice that these machines are capable of taking multiple denominations ($.25 or $.50) there reel glass will show these markings.
Vision – The Vision games machines look identical to S-2000s except that the have a monitor on the upper glass and a plays a bonus game. The monitor appears flush with the glass and not bordered with lights.
Slot Machine Parts Store
Reel Touch – These machines have a round top and inset monitor with an lighted frame. These are 5 reel machines and the reels are back lit have five back-lit reels. The reel-touch are similar in appearance to the S- 2000 many of the internal parts are the same.
Igt Slot Machines Parts
I-Plus – Typically you will find these as either a video slot or video poker. The Game King is an example of a multi-game machine built on the I-Plus platform. They are identifiable by their round top, large video display. The display is a touch screen and used to select the games